[Eisfair] LM-Sensors für Eisfair-1???

[Marcus Roeckrath]

Hallo Detlef,

Detlef Paschke wrote:

> Bei mir ergibt sich bei einem Asus PR-DLS533 (Chip ist wohl der w83781d)
> folgendes:
> Alle Werte werden ohne Formatierung ausgegeben.
> 
> as99127f-i2c-0-2d
> Adapter: SMBus PIIX4 adapter at e800
> in0:          +1.49 V  (min =  +1.20 V, max =  +1.60 V)

In der /etc/sensors3.conf gibt es keine Definitionen für den Chip; daher nur
Ausgabe von Raw-Werten.

> LM_SENSORS_CHIP_1_NAME='w83781d'

Das ergibt in /etc/sensors.conf eine falsche chip-Sektion.

Was steht eigentlich in /etc/sysconfig/lm_sensors?

Es gibt Module (/etc/sysconfig/lm_sensors), die mehrere Chips behandeln; in
der Konfiguration muss hier der Chip stehen; wenn das verschieden vom
Modulnamen ist, verhindert die Eingabeprüfung, dass Du den richtigen Chip
angeben kannst.

Daher deaktiviere diese Eingabeprüfung:

/etc/check.d/lm_sensors:

LM_SENSORS_CHIP_%                LM_SENSORS_CHIP_%_ACTIVE  LM_SENSORS_CHIP_N
        LM_SENSORS_CHIPS_CUI

in

LM_SENSORS_CHIP_%                LM_SENSORS_CHIP_%_ACTIVE  LM_SENSORS_CHIP_N
       NONE

Jetzt kannst Du für den Chip den korrekten Wert as99127f eintragen.

> Eine direkte Eingabe von sensors -c
> /usr/share/doc/lm_sensors/sample.conf/Asus/PR-DLS533.conf (das ist meine
> alte Config) ergibt:
> 
> as99127f-i2c-0-2d

Dann trage doch die Zeilen aus PR-DLS533.conf jetzt ein, allerding fehlen
noch einige, wie die set-Statements für Minimum und Maximum ...

> CPU0 Fan:    3708 RPM  (min =   -1 RPM, div = 2)

Hier fehlt ein set-Statement.

> CPU1 Fan:    3857 RPM  (min = 9926 RPM, div = 2)

Hier fehlt es auch.

> M/B Temp:     +61.0°C  (high =  +0.0°C, hyst = -128.0°C)

Hier auch.

Hier noch eine Standardsektion für Deinen Chip; wenn Du einfach mal sensors
ohne /etc/sensors(3).conf Datei aufrufst, siehst Du (Dein erstes Beispiel
ohne Formatierung), welche Ausgabe (in, temp, fan) überhaupt vorhanden sind
(wohl in0-in6, temp1-temp3, fan1-fan3, cpu0_vid):

chip "as99127f-*"

# Asus won't release a datasheet so this is guesswork.
# Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak,
# Victor G. Marimon and others for their feedback.

# Dual power plane
    label in0 "VCore 1"
    label in1 "VCore 2"
# Single power plane (A7V133, A7M266, CUV4X)
#   label in0 "VCore"
#   ignore in1

    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
# These last two may not make sense on all motherboards.
    label in5 "-12V"
    label in6 "-5V"

    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
    compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
# AS99127F rev.1 (same as w83781d)
    compute in5 -(240/60.4)*@ ,  -@/(240/60.4)
    compute in6 -(90.9/60.4)*@ ,  -@/(90.9/60.4)
# AS99127F rev.2 (same as w83782d)
#   compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
#   compute in6 (3.14 * @) -  7.71 , (@ +  7.71) / 3.14

# Depending on your motherboard, you may have to use any of two formulae
# for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes
# to the driver):
# "I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct
# for those Asus motherboards, which get CPU temperature from internal
# thermal diode (Pentium Coppermine, and above), while no formula is needed
# for Athlon/Duron boards, which use a thermistor in the socket."
# An alternative formula was then found and reported by Victor G. Marimon.

# Asus A7V133, Asus A7M266
#   No compute line is needed
# Asus CUV4X, Asus A7V8X
#   compute temp2 (@*15/43)+25, (@-25)*43/15
# Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C
#   compute temp2 (@*30/43)+25, (@-25)*43/30

# See comments above if temp3 looks bad. What works for temp2 is likely
# to work for temp3 for dual-CPU boards, such as the CUV4X-D.

# Most Asus boards have temperatures settled like that:
    label temp1 "M/B Temp"
    label temp2 "CPU Temp"
# However, some boards have them swapped (A7N8X Deluxe rev.2,
# A7N8X-E Deluxe rev.2, CUV4X):
#   label temp1 "CPU Temp"
#   label temp2 "M/B Temp"
# Most boards have no temp3 by default, except for dual-CPU boards.
#   label temp3 "CPU 2 Temp"
#   ignore temp3

# set limits to  5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage

#    set in0_min cpu0_vid*0.95
#    set in0_max cpu0_vid*1.05
#    set in1_min cpu0_vid*0.95
#    set in1_max cpu0_vid*1.05
#    set in2_min 3.3 * 0.95
#    set in2_max 3.3 * 1.05
#    set in3_min 5.0 * 0.95
#    set in3_max 5.0 * 1.05
#    set in4_min 12 * 0.90
#    set in4_max 12 * 1.10
#    set in5_min -12 * 0.90
#    set in5_max -12 * 1.10
#    set in6_min -5 * 0.95
#    set in6_max -5 * 1.05

# examples for temperature limits
#    set temp1_max      40
#    set temp1_max_hyst 37
#    set temp2_max      52
#    set temp2_max_hyst 47
#    set temp3_max      52
#    set temp3_max_hyst 47

-- 
Gruss Marcus