[Eisfair] Update Base-2.8.5 (Problem)

[Stefan Puschek]

Hallo Uwe,

> um es nochmal zu konkretisieren:
> 
>> SO hier (Anhang) sehen sowohl Monitor (Hardware) als auch
>> ssh-remote-Verbindung (putty) aus. Aufgetreten ist das beim Verwenden
>> des APCUPSD-Paketes.
> 
> Der Zeichensalat entsteht beim Abrufen der USV-Kennwerte (bei mir über 
> ein serielles Kabel).
> 
> Der Zeichensalat geht solange weiter, bis ich den mc öffne ... danach 
> ist der Zeichensatz wieder normal.

ich nehme an, Du meinst das hier:

2020-03-26 14:27:17 apctest 3.14.14 (31 May 2016) suse
Checking configuration ...
sharenet.type = Network & ShareUPS Disabled
cable.type = Custom Cable Smart
mode.type = APC Smart UPS (any)
Setting up the port ...
Doing prep_device() ...

You are using a SMART cable type, so I'm entering SMART test mode
Hello, this is the apcupsd Cable Test program.
This part of apctest is for testing Smart UPSes.
Please select the function you want to perform.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit

Select function number: 1

I am going to run through the series of queries of the UPS
that are used in initializing apcupsd.

Simulating UPSlinkCheck ...
Wrote: Y Got: SM
Attempting to use smart_poll() ...
Sent: Y Got: SM  Good -- smart_poll() works!.

Going to ask for valid commands...
Wrote: a Got: 3.?=.')-89 at ABDEFGKLMNOPQRSUVWXYZabcdefgjklmnopqrsuxyz~
Protocol version is: 3
Alert characters are: ?=
Command characters are: 
^A^N^Z')-89 at ABDEFGKLMNOPQRSUVWXYZabcdefgjklmnopqrsuxyz~

Now running through apcupsd get_UPS capabilities().
NA  indicates that the feature is Not Available

UPS Status: 08
Line quality: FF
Reason for last transfer to batteries: R
Self-Test Status: NO
Line Voltage: 224.6
Line Voltage Max: 227.5
Line Voltage Min: 224.6
Output Voltage: 224.6
Batt level percent: 100.0
Batt voltage: 14.02
UPS Load: 005.2
Line freq: 50.00
Runtime left: 0037
UPS Internal temp: NA
Dip switch settings: NA
Register 1: 00
Register 2: 00
Register 3: 00
Sensitivity: H
Wakeup delay: 000
Sleep delay: 180
Low transfer voltage: 208
High transfer voltage: 253
Batt charge for return: 00
Alarm status: L
Low battery shutdown level: 05
UPS Name: SMART420
UPS Self test interval: ON
UPS manufacture date: 06/02/98
UPS serial number: GS9823647739
Date battery replaced: 14/08/18
Output voltage when on batteries: 230
Nominal battery voltage: 012
Percent humidity: NA
Ambient temperature: NA
Firmware revision: 21.2.I
Number of external batteries installed: NA
Number of bad batteries installed: NA
UPS model as defined by UPS: SMART-UPS 420
UPS EPROM capabilities string: 
uD43127130133136uA43108110112114uI43253257261265lD43106103100097lA43092090088086lI43208204200196e44200155090oD13115oJ13100oI13230s441HMLLq44202050710p443020180300600k4410TLNr443000060180300E443336168ON 
OFF
The EPROM string is 205 characters long!
Hours since last self test: 005.3

That is all for now.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit

Select function number:

hier funktionierts noch (per ssh vom Mac)- alle Pakete aktuell

ALLERDINGS:
ab jetzt ist das Menü vom eisfair-setup "etwas kaputt"
lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk
x eisfair setup  4..          x
tqqqqqqqqqqqqqqqqqqqqqqqqqqqqqu
x 1   System administration   x
x 2   Package administration  x
x 3   Package documentation   x
x 4   Service administration  x
x 5   User administration     x
x                             x
x 0   Exit                    x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj

mit einer neuen ssh-Verbindung ist alles wieder gut - und das Phänomen 
ist schon uralt, hat mich aber nie gestört

HTH

Groetjes
Stefan