[Eisfair] [E1] SSD als Bootplatte

[Rolf Bensch]

Hallo zusammen,

habe eine Bootplatte gegen eine SSD ausgetauscht. Der Betrieb ist 
unauffällig. Allerdings finde ich beim Bootvorgang folgende Meldungen:

#> dmesg
...
[  280.852031] ata3.00: NCQ disabled due to excessive errors
[  280.852040] ata3.00: exception Emask 0x0 SAct 0x37e2 SErr 0x0 action 
0x6 frozen
[  280.852046] ata3.00: failed command: READ FPDMA QUEUED
[  280.852061] ata3.00: cmd 60/08:08:70:d5:ca/00:00:00:00:00/40 tag 1 
ncq dma 4096 in
                         res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852064] ata3.00: status: { DRDY }
[  280.852069] ata3.00: failed command: WRITE FPDMA QUEUED
[  280.852082] ata3.00: cmd 61/08:28:58:8c:5c/00:00:00:00:00/40 tag 5 
ncq dma 4096 out
                         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852085] ata3.00: status: { DRDY }
[  280.852089] ata3.00: failed command: WRITE FPDMA QUEUED
[  280.852101] ata3.00: cmd 61/d8:30:f8:dd:5d/01:00:00:00:00/40 tag 6 
ncq dma 241664 out
                         res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852105] ata3.00: status: { DRDY }
[  280.852108] ata3.00: failed command: WRITE FPDMA QUEUED
[  280.852121] ata3.00: cmd 61/68:38:a0:a0:8f/00:00:00:00:00/40 tag 7 
ncq dma 53248 out
                         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852124] ata3.00: status: { DRDY }
[  280.852128] ata3.00: failed command: WRITE FPDMA QUEUED
[  280.852140] ata3.00: cmd 61/08:40:c0:0f:25/00:00:00:00:00/40 tag 8 
ncq dma 4096 out
                         res 40/00:01:06:4f:c2/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852143] ata3.00: status: { DRDY }
[  280.852147] ata3.00: failed command: SEND FPDMA QUEUED
[  280.852159] ata3.00: cmd 64/01:48:00:00:00/00:00:00:00:00/a0 tag 9 
ncq dma 512 out
                         res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852162] ata3.00: status: { DRDY }
[  280.852166] ata3.00: failed command: READ FPDMA QUEUED
[  280.852179] ata3.00: cmd 60/20:50:c8:30:1e/00:00:00:00:00/40 tag 10 
ncq dma 16384 in
                         res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852182] ata3.00: status: { DRDY }
[  280.852186] ata3.00: failed command: READ FPDMA QUEUED
[  280.852198] ata3.00: cmd 60/08:60:b0:fd:0a/00:00:02:00:00/40 tag 12 
ncq dma 4096 in
                         res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852201] ata3.00: status: { DRDY }
[  280.852205] ata3.00: failed command: READ FPDMA QUEUED
[  280.852217] ata3.00: cmd 60/08:68:68:fd:0d/00:00:00:00:00/40 tag 13 
ncq dma 4096 in
                         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 
0x4 (timeout)
[  280.852220] ata3.00: status: { DRDY }
[  280.852227] ata3: hard resetting link
[  281.332017] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  281.332305] ata3.00: supports DRM functions and may not be fully 
accessible
[  281.333817] ata3.00: supports DRM functions and may not be fully 
accessible
[  281.334917] ata3.00: configured for UDMA/133
[  281.334931] ata3.00: device reported invalid CHS sector 0
[  281.334935] ata3.00: device reported invalid CHS sector 0
[  281.334964] ata3: EH complete
[  281.564809] ata3.00: Enabling discard_zeroes_data
...

Sollte ich mir Gedanken machen? Kann ich da etwas verbessern?

Die Platte wurde per clonezilla kopiert, die Neue hängt am gleichen Port 
wie die Alte.

Gruß Rolf