[Eisfair] [e?==?utf-8?Q?1] smartmon auf aktuellem ?==?utf-8?Q?eisfair-1
Rene Hanke
Rene.Hanke at gmx.net
Fr Jul 29 20:26:47 CEST 2016
Hallo!
Zwar ist meine zweite Platte für das RAID leider noch nicht da, dafür
konnte ich schon etwas testen.
Situation ist folgende:
1. Platte WD Red 1TB an SATA
2. Platte Seagate Pipeline 2TB an USB
Mit dem alten smartmon-Paket wurde die SATA-Platte zumindest erkannt,
war aber nicht in der smartctl-Datenbank:
- - - - - - - - - - - -
eis 2.7.4 # smartctl -a -d sat /dev/sda
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen,
http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD10EFRX-68FYTN0
Serial Number: WD-WCC4J3AKDVR0
Firmware Version: 82.00A82
User Capacity: 1,000,204,886,016 bytes
Device is: Not in smartctl database [for details use: -P
showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jul 29 18:07:49 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection
activity
was never started.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (13680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline
immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 156) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 100 253 021 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 4
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always
- 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 3
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 4
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always
- 4
194 Temperature_Celsius 0x0022 111 111 000 Old_age Always
- 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
- - - - - - - - - - - -
Mit der USB-Platte sah es da schon anders aus. Laut Internet bräuchte
sie den Typus "usbprolific", den gab es aber auch nicht:
- - - - - - - - - - - -
eis 2.7.4 # smartctl -i /dev/sdb
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen,
http://smartmontools.sourceforge.net
/dev/sdb: Unknown USB bridge [0x067b:0x2773 (0x100)]
Smartctl: please specify device type with the -d option.
Use smartctl -h to get a usage summary
- - - - - - - - - - - -
eis 2.7.4 # smartctl -i -d usbprolific /dev/sdb
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen,
http://smartmontools.sourceforge.net
/dev/sdb: Unknown USB device type 'usbprolific'
=======> VALID ARGUMENTS ARE: ata, scsi, sat[,N][+TYPE], usbcypress[,X],
usbjmicron[,x][,N], usbsunplus, marvell, areca,N, 3ware,N, hpt,L/M/N,
megaraid,N, cciss,N, test <=======
Use smartctl -h to get a usage summary
- - - - - - - - - - - -
Nun habe ich die Dateien "smartctl", "smartd" und "update-smart-drivedb"
aus dem Archiv von Marcus in "/usr/sbin" kopiert sowie "drivedb.h" in
"/usr/share/smartmontools", welchse noch anzulegen war.
Die Rechte wurden jeweils aus rwxr-xr-x gesetzt und nun sieht es so
aus:
1. Platte (SATA WD Red 1TB):
- - - - - - - - - - - -
eis 2.7.4 # smartctl -a -d sat /dev/sda
smartctl 6.5 2016-05-07 r4318 [i686-linux-3.2.81-eisfair-1-SMP] (local
build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD10EFRX-68FYTN0
Serial Number: WD-WCC4J3AKDVR0
LU WWN Device Id: 5 0014ee 2b7e4dec8
Firmware Version: 82.00A82
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Jul 29 18:32:02 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection
activity
was never started.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (13680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline
immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 156) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 100 253 021 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 4
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always
- 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 4
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 4
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always
- 4
194 Temperature_Celsius 0x0022 112 111 000 Old_age Always
- 31
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
- - - - - - - - - - - -
2. Platte (USB Seagate Pipeline 2TB):
- - - - - - - - - - - -
eis 2.7.4 # smartctl -a -d sat /dev/sdb
smartctl 6.5 2016-05-07 r4318 [i686-linux-3.2.81-eisfair-1-SMP] (local
build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Video 3.5 HDD
Device Model: ST2000VM003-1CT164
Serial Number: W1H2FCTX
LU WWN Device Id: 5 000c50 06ac71ea4
Firmware Version: SC23
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5900 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Jul 29 18:34:23 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers
missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection
activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 107) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline
immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
No Offline surface scan
supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 271) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10b9) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 099 006 Pre-fail Always
- 113296984
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 22
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always
- 23778852
9 Power_On_Hours 0x0032 098 098 000 Old_age Always
- 2457
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 19
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 2
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always
- 130
190 Airflow_Temperature_Cel 0x0022 070 063 045 Old_age Always
- 30 (Min/Max 25/30)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 11
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 25
194 Temperature_Celsius 0x0022 030 040 000 Old_age Always
- 30 (0 17 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 65
-
# 2 Short offline Aborted by host 30% 65
-
# 3 Short offline Completed without error 00% 64
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
- - - - - - - - - - - -
Geplottet wird für beide Laufwerke. Was nicht funktioniert im nächsten
Posting.
René
Mehr Informationen über die Mailingliste Eisfair