[Eisfair] smart via usb. Eine geht, die andere nicht.

[Kay Martinen]

Hallo

Hier habe ich zwei USB Platten an meinem Fileserver. eine 2 TB Hitachi 
am internen USB 2.0 und eine 4 TB USB 3.0 Platte die sich nur als 
Intenso ausgibt.


> file # smartctl -i -d sat,auto /dev/sde
> smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.9.196-eisfair-64-VIRT] (local build)
> Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
> 
> === START OF INFORMATION SECTION ===
> Vendor:               Intenso
> Product:              External USB 3.0
> Revision:             5438
> Compliance:           SPC-4
> User Capacity:        4,000,787,013,632 bytes [4.00 TB]
> Logical block size:   4096 bytes
> Physical block size:  32768 bytes
> Lowest aligned LBA:   12032
> Logical Unit id:      0x50564c4937313120
> Serial number:        20161119010031
> Device type:          disk
> Local Time is:        Wed Jan 15 22:49:53 2020 CET
> SMART support is:     Unavailable - device lacks SMART capability.
> 
> file # smartctl -i -d sat,auto /dev/sdf
> smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.9.196-eisfair-64-VIRT] (local build)
> Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
> 
> === START OF INFORMATION SECTION ===
> Vendor:               Hitachi
> Product:              HUA722020ALA331
> User Capacity:        2,000,398,933,504 bytes [2.00 TB]
> Logical block size:   512 bytes
> Physical block size:  131072 bytes
> Lowest aligned LBA:   10528
> Formatted with type 2 protection
> 64 protection information intervals per logical block
> 512 bytes of protection information per logical block
> scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
>>> Terminate command early due to bad response to IEC mode page
> A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
> file #

Was kann ich da noch machen. mit zwei -T permissive bringt das auch 
nichts sinnvolles zutage.

Die 4 TB zeigt bei hdparm fehler.

> /dev/sde:
> SG_IO: bad/missing sense data, sb[]:  70 00 05 00 00 00 00 0a 00 00 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>  multcount     =  0 (off)
>  readonly      =  0 (off)
>  readahead     = 256 (on)
>  geometry      = 486401/255/63, sectors = 7814037136, start = 0

Auch mit -i oder -I kommen da fehler.

> file # hdparm -I /dev/sde
> 
> /dev/sde:
> SG_IO: bad/missing sense data, sb[]:  70 00 05 00 00 00 00 0a 00 00 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 
> ATA device, with non-removable media
> Standards:
>         Likely used: 1
> Configuration:
>         Logical         max     current
>         cylinders       0       0
>         heads           0       0
>         sectors/track   0       0
>         --
>         Logical/Physical Sector size:           512 bytes
>         device size with M = 1024*1024:           0 MBytes
>         device size with M = 1000*1000:           0 MBytes
>         cache/buffer size  = unknown
> Capabilities:
>         IORDY not likely
>         Cannot perform double-word IO
>         R/W multiple sector transfer: not supported
>         DMA: not supported
>         PIO: pio0

Bei der anderen dagegen:

> file # hdparm -i /dev/sdf
> 
> /dev/sdf:
>  HDIO_GET_IDENTITY failed: Invalid argument
> file # hdparm -I /dev/sdf
> 
> /dev/sdf:
> 
> ATA device, with non-removable media
>         Model Number:       Hitachi HUA722020ALA331
>         Serial Number:      YBKK0TAF
>         Firmware Revision:  JKAOA3NH
>         Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6; Revision: ATA8-AST T13 Project D1697 Revision 0b
> Standards:
>         Used: unknown (minor revision code 0x0029)
>         Supported: 8 7 6 5
>         Likely used: 8

... und da hörts noch nicht auf.

mit ARGS -H hab ich im smart setup sdf soweit gebracht das ich die 
Smart-Parameter bekomme. U.a. die Temperatur u.s.w.

Nur bei sde, die sich nur als intenso meldet nicht. Gar nichts.

Was kann ich da tun?


Kay

-- 
Sent via SN (Eisfair-1)