[Eisfair] Mail (exim) auf TLS einrichten

[Martin Faderbauer]

Hallo NG

ich versuche das MailPaket auf TLS Umzustellen da inzwischen von
Versicherungen und Banken ein Mailtransport per TLS gefordert wird.

wenn ich bei den MX Toolbox den Server abfrage dann bekomme ich.

220 mail.xxxx.at ESMTP Exim 4.94.2 Sat, 28 May 2022 14:51:45 +0200
	Test 	Result 	
Status Warning	SMTP TLS Warning - Does not support TLS. 	Information
More Info
Status Ok	SMTP Reverse DNS Mismatch OK - 80.123.xxx.xxx resolves to
mail.xxxx.at 	
Status Ok	SMTP Valid Hostname OK - Reverse DNS is a valid Hostname 	
Status Ok	SMTP Banner Check OK - Reverse DNS matches SMTP Banner 	
Status Ok	SMTP Connection Time 	0.378 seconds - Good on Connection time 	
Status Ok	SMTP Open Relay OK - Not an open relay. 	
Status Ok	SMTP Transaction Time 	1.231 seconds - Good on Transaction Time 	
Session Transcript:
Connecting to 80.123.xxx.xxx

220 mail.xxx.at ESMTP Exim 4.94.2 Sat, 28 May 2022 14:51:45 +0200 [214 ms]
EHLO keeper-us-east-1c.mxtoolbox.com
250-mail.xxx.at Hello keeper-us-east-1c.mxtoolbox.com [18.205.72.90]
250-SIZE 36700160
250-8BITMIME
250-PIPELINING
250-PIPE_CONNECT
250-AUTH CRAM-MD5
250-CHUNKING
250-PRDR
250 HELP [240 ms]
MAIL FROM:<supertool at mxtoolboxsmtpdiag.com>
250 OK [244 ms]
RCPT TO:<test at mxtoolboxsmtpdiag.com>
550 Relaying not permitted [254 ms]

LookupServer 2230ms

im Mail Paket habe ich folgendes:


 START_SMTP                      =  yes
              ▒
│ SMTP_QUALIFY_DOMAIN             =  xxxx.at
               ▒
│ SMTP_HOSTNAME                   =  mail.xxxx.at
               ▒
│ SMTP_QUEUE_INTERVAL             =  30
               ▒
│ SMTP_QUEUE_OUTBOUND_MAIL        =  no
               ▮
│ SMTP_QUEUE_ACCEPT_PER_CONNECTION=  10
               ▒
│ SMTP_LISTEN_PORT                =
               ▒
│ SMTP_MAIL_TO_UNKNOWN_USERS      =  bounce
               ▒
│ SMTP_ALLOW_EXIM_FILTERS         =  yes
               ▒
│ SMTP_CHECK_RECIPIENTS           =
               ▒
│ SMTP_CHECK_SPOOL_SPACE          =
               ▒
│ SMTP_CHECK_SPOOL_INODES         =
               ▒
│ SMTP_LIMIT                      =  35M
               ▒
│ SMTP_REMOVE_RECEIPT_REQUEST     =  no
               ▒
│ SMTP_SERVER_TRANSPORT           =  tls
               ▒
│ SMTP_IDENT_CALLBACKS            =  no
               ▒
│ SMTP_SERVER_TLS_ADVERTISE_HOSTS =
               ▒
│ SMTP_SERVER_TLS_VERIFY_HOSTS    =
               ▒
│ SMTP_SERVER_TLS_TRY_VERIFY_HOSTS=
               ▒
│ SMTP_SERVER_SSMTP               =  yes
               ▒
│ SMTP_SERVER_SSMTP_LISTEN_PORT   =


was muss ich noch einstellen damit TLS funktioniert?

danke für eure Hilfe

Lg Martin