[Fli4l_dev] njordr 3.7.0-rev22029 / Could not start hostapd - disabling device for safety reasons

[Sebastian Just]

Hallo zusammen,

ich habe gerade mal den aktuellen Tarball ausprobiert - Ich komme von 
einer funktionierenden Konfig mit 3.6.

Nun kommt das WLAN nicht mehr hoch mit folgender Meldung:

(/etc/rc.d/rc130.wlan) ERR: Error 42 while setting up wlan0
(/etc/rc.d/rc130.wlan) ERR: Could not start hostapd - disabling device 
for safety reasons
(/etc/rc.d/rc305.ip-eth) ERR: skipping device wlan0 because of previous 
error on wlan-setup for security reasons
(hardware detection)  #
(hardware detection)  # PCI Devices and drivers
(hardware detection)  #
(hardware detection)  Network controller: Atheros Communications Inc. 
AR928X Wireless Network Adapter (PCI-Express) (rev 01)
(hardware detection)  Driver: 'ath9k'

Die WLAN-Karte ist
# lspci -vvv
00:00.0 Network controller: Atheros Communications Inc. AR928X Wireless 
Network Adapter (PCI-Express) (rev 01)
         Subsystem: Ubiquiti Networks, Inc. Device 4e05
         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B- DisINTx-
         Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
         Latency: 0, Cache Line Size: 64 bytes
         Interrupt: pin A routed to IRQ 25
         Region 0: Memory at feb00000 (64-bit, non-prefetchable) [size=64K]
         Capabilities: [40] Power Management version 2
                 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
         Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0 Enable-
                 Address: 00000000  Data: 0000
         Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
                 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s 
<512ns, L1 <64us
                         ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                 DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
Unsupported-
                         RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                         MaxPayload 128 bytes, MaxReadReq 512 bytes
                 DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- 
AuxPwr- TransPend-
                 LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown, 
Latency L0 <512ns, L1 <64us
                         ClockPM- Suprise- LLActRep- BwNot-
                 LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- 
CommClk+
                         ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                 LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
         Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
                 Vector table: BAR=0 offset=00000000
                 PBA: BAR=0 offset=00000000
         Capabilities: [100] Advanced Error Reporting <?>
         Capabilities: [140] Virtual Channel <?>
         Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
         Kernel driver in use: ath9k

Was sind das für Securityreasons? Was kann ich dagegen tun bzw. wie kann 
ich sie fixen?
In der Doku habe ich zu Securityreasons nichts gefunden.

Danke & viele Grüße,
Sebastian