[Eisfair] Problem mit Eisfax 2.8.8
Detlef Paschke
schabau at t-online.de
Do Jul 11 16:34:31 CEST 2019
Am 11.07.2019 um 12:56 schrieb Holger Bruenjes:
> Hallo Detlef
Hallo Holger,
> Ich habe jetzt Dein MusterFax geklaut und ueber eine Verbindung von
> extern, also ueber das Telefonnetz uebertragen zu mir. Bei beiden
> Versionen eisfax-2.8.7 -> HylaFAX-5.9.9 und eisfax-2.8.8 ->
> HylaFAX-7.0.0 gibt es keine Probleme. Ich habe hier auch noch ein
> ELSA Microlink 56k rumsausen, ich werde das noch mal anhaengen und
> damit Testen.
ich habe mir heute auch mal Zeit genommen und den ganzen Tag
Einstellungen getestet.
Zumindest das Senden von Faxen funktioniert hier jetzt mit eisfax-2.8.8
wieder Problemlos. Getestet mkt einem lokalen Fax als auch mit
Test-Fax-Diensten im Internet. Nach einigem suchen und basteln habe ich
das Modem auf Fax-Class 2.0 eingerichtet. Einige Befehle die im Netz zu
finden sind musste ich anpassen nachdem ich im log "MODEM Command error"
dazu gefunden hatte. Die Konfiguration sieht jetzt so aus.:
#
# Class 2.0 modem configuration for ELSA 33.6 TQV.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 355
FAXNumber: "+49 355 49487224"
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: high
GettyArgs: "-h %l dx_%s"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "EisFAX Server von %%n an %%d Seite %%P von %%T
/ %d.%m.%Y %T"
MaxRecvPages: 25
FaxRcvdCmd: bin/faxrcvd-local
NotifyCmd: bin/notify-local
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # RTS/CTS flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers (e.g. 9) to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9W%s@".
#
ModemDialCmd: ATDT%s
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: ATX3 # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT\Q0
ModemHardFlowCmd: AT\Q3
ModemSoftFlowCmd: AT\Q1
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy
quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,0 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command
Der Empfang von Faxen ist aber immer noch fehlerhaft.
Im log fallen mir dabei diese Zeilen auf.
Jul 11 16:12:51.58: [ 9131]: --> [7:CONNECT]
Jul 11 16:12:51.58: [ 9131]: RECV: begin page
Jul 11 16:12:51.58: [ 9131]: RECV: send trigger 022
Jul 11 16:12:51.58: [ 9131]: <-- data [1]
Jul 11 16:12:51.58: [ 9131]: Copy quality checking performed by modem
Jul 11 16:13:26.58: [ 9131]: RECV: 32763 bytes of data, 1111 total lines
Jul 11 16:13:39.24: [ 9131]: RECV: 12134 bytes of data, 1443 total lines
Jul 11 16:13:39.27: [ 9131]: --> [20:+FPS:2,6AC,EA,0,44C3]
Jul 11 16:13:39.52: [ 9131]: --> [6:+FET:2]
Jul 11 16:13:39.52: [ 9131]: RECV recv EOP (no more pages or documents)
Jul 11 16:13:39.53: [ 9131]: --> [5:ERROR]
Jul 11 16:13:39.53: [ 9131]: MODEM Command error
Jul 11 16:13:39.53: [ 9131]: RECV send RTN (retrain negative)
Bezieht sich das "MODEM Command error" auf "FET:2"?
Das finde ich aber in der Config gar nicht und kann es somit nicht ändern.
> Holger
>
Viele Grüße
Detlef Paschke
--
registered Fli4l-User #00000209
Das "Zitat des Augenblicks" gibt es nur auf
http://www.schabau.goip.de
Mehr Informationen über die Mailingliste Eisfair